01689 606342

This 12v natural copper twin spikelight with 1m pole really looks the part and is also available in 240v (separate listing). The two 60mm diameter spotlights are individually adjustable so can be pointed in completely different directions, such as to highlight low level planting whilst also lighting taller features, or in the same direction for double the light output in one area. The long heads ensure longer LED MR16s can be accommodated with no issues. The long 1m pole has a 45° cut at the base to form a spike, which can be cut to a shorter length if required. The cable exit is situated 400mm from the base, with approximately 5m of cable supplied for ease of installation (less cable joins). Made from natural copper with polished brass detail to the neck of the spotlights, this spike light will weather over time to blend in with it's natural surroundings.

  • Materials:  Natural Copper (non lacquered), Brass, Tempered Glass *see below for more info
  • Voltage: 12v
  • Bulb Holder: 2 x MR16 (12v)
  • Max. Wattage: 50w  per bulb holder
  • IP Rating: IP65
  • Spike Length: 1000mm (1m)
  • Rubber Cable Included: 2 Core (12v) 0.75mm² H05RN-F (approx. 5m)


Choosing the style of a product is only part of the equation you must also think of where that product will be used and how it will be installed. All exterior lighting products on our web site have a IP rating which is explained further in our design ideas section but in simple terms the IP rating is appropriate to each light fitting and its intended application and is therefore fit for purpose. Water ingress is the enemy for outdoor lighting and the products supplied are only as good as the installation as the weakest point is always cable and transformer joints. All joint must be made 100% water tight and this can be done using heat shrink kits, waterproof junction boxes which are then filled with a resin mix. All joints where possible should be made above ground for easy access and reduced water ingress. When installing ground buried lights adequate drainage systems should be put in place especially in clay based soil areas. If possible use ground surface spike lights rather than a buried light.  Mains 240v cable will have less joints than a low voltage installation but care must be taken with the cable runs.

All exterior lights must be installed by a certified NIC EIC electrician and should be signed off by an electrician with Part P certification. all cable joints must be 100% watertight. There are a selection of waterproof jointing kits and boxes available on this web site.

Light output ( Lumens )

The amount of light that is produced by a lamp is called lumens and the more lumens the lamp has the brighter it will be. Lumens work in conjunction with kelvins and should not be taken in isolation of each other. For example if you had a very warm white lamp at 2,700 kelvins and it produced 300 lumens and you then had another lamp which was a cool white 6,000 kelvins which also produced 300 lumens the cooler lamp colour would always appear brighter to the naked eye than the warmer one this is due to the receptors in the eye that react better to a white light spectrum. Another factor on how bright a light may appear is contrast. So if you shine a white 6,000 kelvin light onto a dark wall and a warm 2,700 Kelvin lamp onto a white wall the warmer lamp would appear brighter due to the contrast of the material it is focused on. So when choosing a lamp always take into account the area you want to illuminate and think about Kelvins (colour ),  Lumens ( brightness) and contrast  (colour of area).

Lamp colour ( Kelvins )

The colour of a lamp is defined as a measurement called kelvins. A standard GLS light bulb in your house would be 2,700 kelvins which is in the warm colour spectrum and a lamp with 6,000 kelvins would be at the very cold white spectrum. Getting the right colour temperature of a lamp does matter as the warm colour wavelength helps to soften skin tones and gives a warm soft relaxed feel and at the other end of the scale a 4,000 to 6,000 kelvin lamp colour  would be used in offices or at fast food restaurants to make you feel less comfortable and relaxed and feel more alert. There’s nothing that can sour your opinion of a compact fluorescent  or LED lamp like buying a 4000K or 5000K bulb when you meant to buy a 2700K bulb, or vice-versa. When you buy a new, energy efficient bulb, keep your application and colour scheme in mind and make sure to buy the bulb with a colour temperature to match. 

Item Specifications

colour: stainless steel, black, Satin Silver, Natural Copper, Rustic Bronze
Lamp base: 2 x MR16
Voltage: 220 - 240v, 12 Volt
Max wattage: 50w per bulb holder
IP rating: IP 65
Materials: Natural Copper (non lacquered), Brass, Tempered Glass
cabling: 2 Core (12v) 0.75mm² H05RN-F (approx. 5m)
Ground spike dimensions: Spike Length: 1000mm (1m)