01689 606342

Alto 60 Bollard Light - Stainless Steel IP44 600mm


Alto 240v LED outdoor bollard light constructed from quality stainless steel with distinctive glare louvres, ideal for use along paths, driveways and entrances. Easy to bolt to paving and slabs or by using an optional ground-mount can be installed into concrete prior to electrical installation.

Additional, galvanised ground spike is also available for installation in planting and lawn areas. Opal glass diffuser and metal louvres help stop glare from the lamp and will work with most PIR and Photocell sensor systems (see lamps and installation materials.) Alto stainless steel bollard lights are 60cm high and accept E27 (large screw) LED lamps - ideal for driveways where regular use requires an energy saving, long life, light source.

Lower powered or dimmable lamps available for softer ambient lighting around garden paths, decking and terraces  ( Order lamps separately)

Colour/Finish: 304 Stainless Steel
IP Rating: IP44
Construction: 304 Stainless Steel body and opal glass diffuser
Input Voltage: 240v
Lamp Type: E27 - Order lamps separately
Installation:

Pre-wired with 2m rubber cable for connection via T9969 underground joint kit: the installer may shorten the fitted cable to make a weatherproof connection inside the base of the light.  

Using a single RCD for large numbers of 240v fittings is not recommended due to the risk of nuisance tripping. We advise the use of separate RCD protection for each circuit and a maximum of 12 fittings per RCD. Where a garden lighting installation of more than 12 spike mount or recessed lights per circuit is proposed, we suggest the installation of 12v units with transformers, which results in a significantly higher fault tolerance and reliability in the total installation.


Installation 

All exterior lighting products on our website have an IP rating which is explained further in our design ideas section but in simple terms the IP rating is appropriate to each light fitting and its intended application and is therefore fit for purpose. Water ingress is the enemy for outdoor lighting and the products supplied are only as good as the installation as the weakest point is always cable joints. All joints must be made 100% water tight and this can be done using IP68 inline connectors, waterproof junction boxes which are then filled with a resin or gel mix. All joints where possible should be made above ground for easy access and reduced water ingress. When installing ground buried lights adequate drainage systems should be put in place especially in clay based soil areas. Also mains cable should be SWA rubber and not PVC.


All exterior lights must be installed by a certified NIC EIC electrician and should be signed off by an electrician with Part P certification. All cable joints must be 100% watertight. There are a selection of waterproof jointing kits and boxes available on this web site.

H05RN-F  3 Core Rubber Sheathed Mains Cable 1.5mm is recommended but do not use PVC flex cable as this can cause poor connections for the cable glands/joints and will lead to capillary action.


Lamp colour ( Kelvins )
 

The colour of a lamp is defined as a measurement called kelvins. A standard GLS light bulb in your house would be 2,700 kelvins which is in the warm colour spectrum and a lamp with 5,000 kelvins would be at the very cold white spectrum. Getting the right colour temperature of a lamp does matter as the warm colour wavelength helps to soften the tone of the area and gives a warm soft relaxed feel and ideal for colourful flower beds and rockery areas especially with wooden bark and at the other end of the scale a 4,000 to 5,000 kelvin lamp colour would be used against a light background such as white walls or to accentuate grey blueish foliage in shrubs and small trees.  When you buy a new, energy efficient bulb, keep your application and colour scheme in mind and make sure to buy the bulb with a colour                    temperature to match. 


                                                             

Item Specifications

Lamp base: E27
Overall diameter: 160mm including base
Voltage: 220 - 240v
IP rating: IP 44
Materials: stainless steel 304
Height: 600mm
diameter: 120mm