01689 606342

Navigator eye, 12v, 1w led step light, coper, warm white, IP67


                                                                          ( Requires a 12v transformer )


The Navigator Eye is a low energy, high output white LED recessed light which consumes a small amount of power and stays cool to the touch. The warm white LED produces a wide 80 degree beam diffused by the 28mm diameter frosted lens to provide soft lighting compatible with the colour of halogen garden lighting. Install it to light across individual steps or in a wall about 40cm above a patio or deck.

Colour/Finish: Natural copper weathers to a mottled brown finish which blends well with red brick and timber, especially darker hardwood decking.

Construction: Long life high-output LED resin-encapsulated behind a frosted glass lens in a stainless steel case. The case has a spring mount which locates the light in a sleeve used to prepare positions in concrete, paving or walls. They can be recessed without the sleeve in decking sleeper walls and other materials using a 44mm hole saw. Diameter 60mm (sleeve 48mm; 44mm cutout without sleeve); recess depth 75mm.

Input Voltage: 12v 2.2W: NAVIGATORS should be connected to 1.5mm or 2.5mm ground burial low voltage cable with a heat-shrink crimped-connector weatherproof Joint Kit - T9962 Cable Joint Kit (for connecting to the end of a cable) or T9963 Cable Splice Kit (for connecting into a run of cable).

NAVIGATORS should be powered by 12v dc power supply. Do not use an electronic transformer to power Navigator LED lights. If powering from a 12v 20va or 50va ac wire-wound transformer, ensure the transformer is loaded to at least 75% of nominal rating.

Lamp Type: 1w Luxeon warm white led. 2.2w total.

The top section of this LED light can be unscrewed to allow the insertion of theatrical coloured lenses to enable you to customise your garden lighting system.

Installation

Navigator lights must be wired in Parallel and can be arranged in custom layouts using cable joint kits and 1.5mm cable, which is more flexible than kit-type products. Connect to the end of a low voltage cable using T9962 cable joint kit; for splicing into a run of cable use T9963 cable splice kit..

Exterior Low voltage light fittings are the ideal choice for outside lighting projects as they are safe to run compared to a mains 240v supply. The installation of exterior lighting is generally the weakest point and it is therefore imperative that the installer has previous experience of installing the lighting system. All joints must be 100% water tight and where possible keep all transformers above ground. Heat shrink kits and resin filled boxes and magic gel are available from our web site to complete a good waterproof installation. It is equally important to allow for adequate drainage under each light fitting especially if you are in a clay based soil area where water drainage could be a problem.  In these type of areas we recommend you have surface lights rather than ones buried in the ground. Ensure that your installer is NIC EIC certified and has done exterior lighting installations before.


Lamp colour ( Kelvin's )

The colour of a lamp is defined as a measurement called kelvins. A standard GLS light bulb in your house would be 2,700 kelvins which is in the warm colour spectrum and a lamp with 5,000 kelvins would be at the very cold white spectrum. Getting the right colour temperature of a lamp does matter as the warm colour wavelength helps to soften the tone of the area and gives a warm soft relaxed feel and ideal for colourful flower beds and rockery areas especially with wooden bark and at the other end of the scale a 4,000 to 5,000 kelvin lamp colour would be used against a light background such as white walls or to accentuate grey blueish foliage in shrubs and small trees.  When you buy a new, energy efficient bulb, keep your application and colour scheme in mind and make sure to buy the bulb with a colour temperature to match. Coloured filters are good to use with the LED bulbs too especially in winter using green filters give the appearance the trees are still in leaf.


                                                        


A guide to lighting steps







Example of 12v transformer loadings


                                    
              

Item Specifications

colour: Natural Copper, stainless steel 316
Voltage: 12 Volt
IP rating: IP 67
Bulb Type: LED
Lamp Watts: 1w Luxeon warm white led. 2.2w total
colour temperature: 3000k Warm White, 4000k cool white