All outdoor lighting should be installed by a certified PART P, NIC EIC electrical contractor to ensure a safe and water tight installation.
Choosing the style of a product is only part of the equation you must also think
of where that productwill be used and how it will be installed. All exterior lighting
products on our web site have a IP rating which is explained further in our design
ideas section but in simple terms the IP rating is appropriate to each light fitting
and its intended application and is therefore fit for purpose. Water ingress is the
enemy for outdoor lighting and the products supplied are only as good as the installation
as the weakest point is always cable and transformer joints. All joint must be made
100% water tight and this can be done using heat shrink kits, waterproof junction
boxes which are then filled with a resin mix. All joints where possible should be
made above ground for easy access and reduced water ingress. When installing ground
buried lights adequate drainage systems should be put in place especially in clay
based soil areas. If possible use ground surface spike lights rather than a buried
light. Mains 240v cable will have less joint than a low voltage installation
but care must be taken with the cable runs.
The colour of a lamp is defined as a measurement called kelvins. A standard GLS
light bulb in your house would be 2,700 kelvins which is in the warm colour spectrum
and a lamp with 6,000 kelvins would be at the very cold white spectrum. Getting the
right colour temperature of a lamp does matter as the warm colour wavelength helps
to soften skin tones and gives a warm soft relaxed feel and at the other end of the
scale a 4,000 to 6,000 kelvin lamp colour would be used in offices or a fast
food restaurants to make you feel less comfortable and relaxed and more alert. There’s
nothing that can sour your opinion of a compact fluorescent or LED lamp like
buying a 4000K or 5000K bulb when you meant to buy a 2700K bulb, or vice-versa. When
you buy a new, energy efficient bulb, keep your application and colour scheme in mind
and make sure to buy the bulb with a colour temperature to match.
The amount of light that is produced by a lamp is called lumens and the more lumens the lamp has the brighter it will be. Lumens work in conjunction with kelvins and should not be taken in isolation of each other, for example if you had a very warm white lamp at 2,700 kelvins and it produced 300 lumens and you then had another lamp which was a cool white 6,000 kelvins which also produced 300 lumens the cooler lamp colour would always appear brighter to the naked eye than the warmer one this is due to the receptors in the eye that react better to a white light spectrum. Another factor on how bright a light may appear is contrast so if you shine a white 6,000 kelvin light on to a dark wall and a warm 2,700 kelvin lamp on to a white wall the warmer lamp would appear brighter due to the contrast of the material it is focused on. So when choosing a lamp always take in to account the area you want to illuminate and think about Kelvins ( colour ), Lumens ( brightness) and contrast ( colour of area )
Choosing the right lamp is a combination of 3 main factors, Lumen's, Kelvins and
efficiency. There are other factors but not so relevant for exterior lighting products.
Efficiency matters because you want the maximum light out put possible ( Lumen's )
from the minimum amounts of watts consumed. The latest LED technology and compact
fluorescent lamps are amongst the most efficient you can buy today. An example would
be to change a mains halogen GU10 35w lamp to a ECO friendly GU10 5w LED lamp. The
same be done by changing the older GLS light bulb for a compact fluorescent lamp.
Reduced energy bills with no loss of light output helps the environment and reduce
your energy bills.
All the luminaries on our web site have been specifically designed fit for purpose and assigned a relevant IP rating which denotes the amount of protection that is required from water and dust. More information on IP ratings can be found in the design ideas section on this web site.
|colour:||white, black, stainless steel 304|
|Finish:||Satin black paint & clear glass|
|Dimensions:||110mm height x 95mm projection x 80mm width|
|Energy Rating:||Energy compatible|
|Material:||Metal & glass|
|Benefit:||Suitable for use with energy compatible lamps|
|Bulb Type:||1 x GU10|