01689 606342

Rox, wall mounted down only garden light, ES111 lamp, mains 240v, brushed aluminium, IP44

Large wall mounted down light that uses a 50w max 24 degree GU10 ES111 lamp to give high output and a medium beam angle.
Modern design in a nice clean body that is easy to clean. Low glare due to the nature of the beam angle and good to illuminate a facade of a building.

A 9w LED lamp option is also available for this fitting and has a 25 degree beam angle, warm white in colour and 333 lumens.

Please ensure that your out door lighting is installed by a certified NIC EIC electrical contractor to ensure a safe and water tight connection.

Lamp colour ( Kelvins )

The colour of a lamp is defined as a measurement called kelvins. A standard GLS light bulb in your house would be 2,700 kelvins which is in the warm colour spectrum and a lamp with 6,000 kelvins would be at the very cold white spectrum. Getting the right colour temperature of a lamp does matter as the warm colour wavelength helps to soften skin tones and gives a warm soft relaxed feel and at the other end of the scale a 4,000 to 6,000 kelvin lamp colour  would be used in offices or a fast food restaurants to make you feel less comfortable and relaxed and more alert. There’s nothing that can sour your opinion of a compact fluorescent  or LED lamp like buying a 4000K or 5000K bulb when you meant to buy a 2700K bulb, or vice-versa. When you buy a new, energy efficient bulb, keep your application and colour scheme in mind and make sure to buy the bulb with a colour temperature to match. 

Kelvin colour chart


Light output ( Lumen's )

The amount of light that is produced by a lamp is called lumen's and the more lumen's the lamp has the brighter it will be. Lumen's work in conjunction with kelvins and should not be taken in isolation of each other, for example if you had a very warm white lamp at 2,700 kelvins and it produced 300 lumen's and you then had another lamp which was a cool white 6,000 kelvins which also produced 300 lumen's the cooler lamp colour would always appear brighter to the naked eye than the warmer one this is due to the receptors in the eye that react better to a white light spectrum. Another factor on how bright a light may appear is contrast so if you shine a white 6,000 kelvin light on to a dark wall and a warm 2,700 kelvin lamp on to a white wall the warmer lamp would appear brighter due to the contrast of the material it is focused on. So when choosing a lamp always take in to account the area you want to illuminate and think about Kelvins ( colour ),  Lumen's ( brightness) and contrast  ( colour of area )


Choosing the style of a product is only part of the equation you must also think of where that product will be used and how it will be installed. All exterior lighting products on our web site have a IP rating which is explained further in our design ideas section but in simple terms the IP rating is appropriate to each light fitting and its intended application and is therefore fit for purpose. Water ingress is the enemy for outdoor lighting and the products supplied are only as good as the installation as the weakest point is always cable and transformer joints. All joint must be made 100% water tight and this can be done using heat shrink kits, waterproof junction boxes which are then filled with a resin mix. All joints where possible should be made above ground for easy access and reduced water ingress. When installing ground buried lights adequate drainage systems should be put in place especially in clay based soil areas. If possible use ground surface spike lights rather than a buried light.  Mains 240v cable will have less joint than a low voltage installation but care must be taken with the cable runs.

Energy efficient lamps

Choosing the right lamp is a combination of 3 main factors, Lumen's, Kelvins and efficiency. There are other factors but not so relevant for exterior lighting products.  Efficiency matters because you want the maximum light out put possible ( Lumen's ) from the minimum amounts of watts consumed. The latest LED technology and compact fluorescent lamps are amongst the most efficient you can buy today. An example would be to change a mains halogen GU10 35w lamp to a ECO friendly GU10 5w LED lamp. The same be done by changing the older GLS light bulb for a compact fluorescent lamp. Reduced energy bills with no loss of light output helps the environment and reduce your energy bills.

IP Rating

All the luminaries on our web site have been specifically designed fit for purpose and assigned a relevant IP rating which denotes the amount of protection that is required from water and dust. More information on IP ratings can be found in the design ideas section on this web site.


                                                                                                                Mains 240v
Easy clean
Twin lamp
Brushed aluminium
High light output

Item Specifications

colour: aluminium brushed
Lamp base: GU10
Lamp description: ES111 230 V max 75 Watt
Overall diameter: 12.5 cm
Weight: 0.900 kg
Voltage: 230 Volt
Max wattage: 75 Watt
IP rating: IP 44
Materials: aluminium
Height: 16 cm
Depth: 13 cm