01689 606342

20w Floodlight 1600lm IP66 Rustic Brown 2700K C/w Spike & Shield


The PF20W 20w floodlight is a small easy to install versatile Plug&Play garden light. The built-in warm white 2700k 1600lm LEDs is perfect for lighting trees. The easily adjustable head also makes this a useful light for wall washing. The optional Glare shield, supplied, easily attaches with the provided bolts. The Plug&Play plugs can be cut off to facilitate hard wiring into wire wound transformers only.

Spike mount 20cm. Spike is black.

IP Rating: IP66
Colour: Rustic brown 
Construction: Powder coated aluminium body 
Input: 12v
Light Source: Integral 20w white 2700K 
Light Output: 1600lm 
Beam Angle  H 85° by V 120°
Installation

1.5m of 2 core cable with male IP44 2-pin input connector to plug into a Plug&Play transformer.

Not suitable for electronics power supplies

Lamp colour ( Kelvins )
 

The colour of a lamp is defined as a measurement called kelvins. A standard GLS light bulb in your house would be 2,700 kelvins which is in the warm colour spectrum and a lamp with 5,000 kelvins would be at the very cold white spectrum. Getting the right colour temperature of a lamp does matter as the warm colour wavelength helps to soften the tone of the area and gives a warm soft relaxed feel and ideal for colourful flower beds and rockery areas especially with wooden bark and at the other end of the scale a 4,000 to 5,000 kelvin lamp colour would be used against a light background such as white walls or to accentuate grey blueish foliage in shrubs and small trees.  When you buy a new, energy efficient bulb, keep your application and colour scheme in mind and make sure to buy the bulb with a colour                    temperature to match. 

Installation 12v

Choosing the style of a product is only part of the equation you must also think of where that product will be used and how it will be installed. All exterior lighting products on our web site have an IP rating appropriate to each light fitting and its intended application and is therefore fit for purpose. Water ingress is the enemy for outdoor lighting and the products supplied are only as good as the installation. The weakest point is always cable joints. All joints must be made 100% watertight and this can be done using IP68 cable connectors and/or waterproof junction boxes which are then filled with a re-enterable liquid gel mix. All joints where possible should be made above ground for easy access and reduced water ingress. When installing ground buried lights adequate drainage systems should be put in place especially in clay-based soil areas. If possible, use ground surface spike lights rather than a buried light.  Care must be taken with the cable runs and not to install transformers more than 30 metres away from the furthest fitting to avoid any voltage drop. Cabling should be 2 core Rubber HO5RN-F or HO7RN-F and not PVC. PVC leads to capillary action over time especially with UV degradation. Always check the correct type of transformer you need for your fittings. We recommend wiring in parallel with Toroidal AC and LED DC drivers. But when using Milliamp mA LED drivers, they should always be wired in series. Plug and Play kits are simply a case of daisy chaining the fittings via plug and play junction boxes, connectors and extension cables using a 2-pin plug arrangement. These Plug and Play fittings should only be used for small domestic projects due to voltage drop over 5 metres.

All exterior lights must be installed by a certified NIC EIC electrician and should be signed off by an electrician with Part P certification. There are a selection of waterproof jointing kits and boxes available on this web site.

                                                        

Item Specifications

colour: Rustic Brown
IP rating: IP 66
Materials: Powder Coated aluminium body
Width: 180mm
Height: 190mm
Depth: 41mm
Lumens: 1600
Bulb Type: integral LED
watts: 20w
colour temperature: 2700k warm white
cabling: 0.75mm 2 Core (H05RN-F) 1.5m
additional information: Plug & Play
Warranty: 2 Years