The DuoMarka is an elegant recessed light suitable for illuminating steps and outlining other areas in the garden, mounted in the ground, walls or decking. It is made from high quality marine grade 316 stainless steel which has an even greater resistance to pitting corrosion / rusting than other lower grade steel.
This fitting is available in Brass and Copper too in both 12v and 240v along with the 12v version in Stainless Steel. Codes, LLDUOBR-12P, LLDUOBR-240v, LLDUOCP-12P, LLDUOSS-12P3, LLDUOCP-240v and LLDUOSS-240v
Please note: This fitting must be installed with the mounting sleeve and additional rubber seal. If the sleeving and seal is not used, the Guarantee will be void. Not for use in areas prone to water-logging or flooding.
The DuoMarka has two conical sections on one side of the top of the fitting, which allows a 180º diffusion of light through a clear lens without glare. The slightly domed surface makes this the ideal shape for mounting on decking, a driveway, a patio or any other areas where a walk over facility is required. The front bezel is threaded, and attaches to a steel body by screwing together with no external screws or fixings which results in a neater overall finish. This also means no tools are required to change the GU10 lamp (LED recommended).
The robust black plastic sleeve will be built into the wall during construction or retrofitted into a drilled out hole. The main part of the light then pushes into the tube, where it is held firmly in place, leaving only the streamline front dome on show.
CARE OF STAINLESS STEEL – TIPS
Contrary to popular belief, Stainless steel needs looking after; especially in exposed and coastal areas. If not cleaning on a regular basis, the acid that is ever present in the air ( and salt in coastal areas) will affect the surface causing pitting and even rust like staining (known as ‘Tea staining’ ) to appear.
To keep your lights looking good, simply wipe clean the outside with a damp cloth and then dry once a month, (more frequently in coastal areas). Specialist stainless steel cleaning products can be used (We recommend and stock ‘Kilrock stainless steel cleaner’) but never use an ABRASIVE cleaner. In extreme conditions we recommend applying 2 coats of Clear lacquer to protect the steel surface. (We recommend and stock ‘Simoniz’ clear lacquer).
240v IN-GROUND LIGHTS
240v fittings can be affected by damp conditions, typically when located outdoors. When a fitting is located outside in the cold air combined with the heat produced by the lamp inside, it is inevitible that condensation will occur, just as it does on bedroom windows in the home. If too much condensation is produced, this could result in the fitting tripping, especially in these types of fittings where a drainage hole is not possible. To combat this, we include silica gel with all Duomarka 240v in-ground lights to soak up any excess moisture – these should not be removed but replaced periodically and fittings checked. If any water is sitting in the fitting, this should be tipped out and the fitting safely dried out. Condensation can be more prominent when the fitting has been opened on a damp day, as the damp air will then be trapped inside when re-sealed. Therefore it is recommended that any maintenance, including changing bulbs, is performed on a dry day. An additional practice to be put in place is to apply Lithium Grease to the bulb holder / bulb which acts as an additional seal to prevent tripping. Although this prevents tripping, the fittings will still need to be checked and dried out should water sit inside the fitting. For extra protection, the Duomarka can also be filled with Wiska Gel (electrical insulation).
|Beam Angle:||180 degree two slots|
|colour:||Natural Copper, Brass, stainless steel 316|
|Voltage:||12v, 220 - 240v|
|IP rating:||IP 67|
|Dimensions:||(Diam.) 90mm x (Length) 105mm|
|Benefit:||3 metre cable so less joints needed|
|Material Finish:||316 Stainless Steel|
|Guarantee:||2 Years, Reduced 1 year warranty period for cable|
|mounting:||Mounting Hole Size: 70mm + 2 x 9mm overlap|
|installation width:||70mm for sleeve plus 7mm edges total width 84mm|