01689 606342

Micro Waymarker LED Recessed Light 90° -12/24v DC-3w-100lm-2700K-IP67- 316 Stainless Steel


The Micro Waymarker 90 recessed LED light is compatible with both 12v and 24v DC powersupplies. 90° light output from a single window. It is useful where you want to cast light across a path or drive edge without casting light backwards onto planting or other finishes behind.  The Micro Waymarker is an outdoor LED light with a flush glass lens, fitted to the top of the dome, preventing debris from settling and blocking the lightoutput The light is located by an "O" ring on the body into a sleeve tube so that no external screw fixings are visible. It may also be used as a deck light.          
                          
The fitting is constructed from a tubular aluminium body which push fits into an aluminium sleeve (tube) where it is held firmly in place by an O-ring, leaving a front plate with no visible fixing screws.  It as a 1.5m 2 core cable.  The top bezel plate is 316 grade stainless steel.

3w warm white LED colour temperature 2700k giving out 100 lumens.  

The life span of the LED is approximately 50,000 hours.

Sleeve depth 90mm x 39mm diameter.
Depth of fitting 53mm. Overall depth including the domed bezel 70.5mm.
Diameter of Bezel 60mm.


The aluminium sleeve is built into the floor/paving during construction or retrofitted into a hole cut with a coring bit: the light pushes into the tube, where it is held firmly in place by an o-ring, leaving a front plate with no visible fixing screws. Suitable drainage should be provided below each fitting to prevent water logging. Micro Waymarkers should not be installed in ground subject to water loggingConnect input cable to cable from transformer using T9962 cable joint or T9963 cable splice kit or T9969 underground joint kit  

 3 Year warranty with the following exclusions: Damage by machinery, animals or the use of incorrect cleaning materials. Damage due to incorrect installation practices. Responsibility for 3rd party cost: indirect or consequential loss.


                                         

Installation 12v/24v

Choosing the style of a product is only part of the equation you must also think of where that product will be used and how it will be installed. All exterior lighting products on our web site have an IP rating appropriate to each light fitting and its intended application and is therefore fit for purpose. Water ingress is the enemy for outdoor lighting and the products supplied are only as good as the installation. The weakest point is always cable joints. All joints must be made 100% watertight and this can be done using IP68 cable connectors and/or waterproof junction boxes which are then filled with a re-enterable liquid gel mix. All joints where possible should be made above ground for easy access and reduced water ingress. When installing ground buried lights adequate drainage systems should be put in place especially in clay-based soil areas. If possible, use ground surface spike lights rather than a buried light.  Care must be taken with the cable runs and not to install transformers more than 30 metres away from the furthest fitting to avoid any voltage drop. Cabling should be 2 core Rubber HO5RN-F or HO7RN-F and not PVC. PVC leads to capillary action over time especially with UV degradation. Always check the correct type of transformer you need for your fittings. We recommend wiring in parallel with Toroidal AC and LED DC drivers. But when using Milliamp mA LED drivers, they should always be wired in series. Plug and Play kits are simply a case of daisy chaining the fittings via plug and play junction boxes, connectors and extension cables using a 2-pin plug arrangement. These Plug and Play fittings should only be used for small domestic projects due to voltage drop over 5 metres.

All exterior lights must be installed by a certified NIC EIC electrician and should be signed off by an electrician with Part P certification. There are a selection of waterproof jointing kits and boxes available on this web site.                      

Item Specifications

Beam Angle: 60 degree
colour: stainless steel 316
Installation depth: 90mm sleeve x 39mm diameter
Voltage: 12v/24v
IP rating: IP 67
Materials: stainless steel 316
Height: 53mm
Feature: 360 degree from 3 windows, 90 degree from 1 single window
Lumens: 100
Material Finish: 316 Stainless Steel
Bulb Type: integral LED
diameter: 60mm
watts: 3 watt
lamp life: 50000 hours
colour temperature: 2700 warm white
cabling: 2 Core 0.75mm² H05RN-F Rubber Cable (1.5m)
Warranty: 3 Years
overall length: 70.5mm