01689 606342

     

Navigator Mono 12v DC 316 Stainless Steel Recessed Deck Light 4000k 0.5w 60 Lumens IP65


The E3211WNN is a white LED deck and recessed light which consumes a tiny amount of power and stays cool to the touch, adding a stylish modern element to a garden lighting scheme. The Navigator Mono are used to mark out the shape of a deck, patio or terrace, to outline paths and light small steps. To outline a deck or patio space with a distinctive shape, start at the corners of the decking or paving and space lights about 0.8 - 1.2 metres apart
Accessories: The top section can be unscrewed to allow the insertion of dichroic coloured lenses to enable you to customise your garden lighting.

316 stainless steel is a popular choice for modern garden settings .

Each light contains long life high-output LED resin-encapsulated behind a frosted glass lens in a stainless steel bezel. The case has a spring mount which locates the light in a sleeve used to prepare positions in concrete, paving or walls.  Comes supplied with 1m H05RN two core cable. They can be recessed without the sleeve in decking, sleeper walls and other materials using a 38mm wood drill bit.

12v 0.5w: NAVIGATORS should be powered by 12v dc power supply. Do not use an electronic transformer to power Navigator LED lights. If powering from a 12v  ac wire-wound transformer, ensure transformer is loaded to at least 60% of nominal rating.

Navigator lights can be arranged in custom layouts using cable joint kits and 1.5mm cable, which is more flexible than kit-type products. Connect to the end of a low voltage cable using T9962 cable joint kit; for splicing into a run of cable use T9963 cable splice kit.

Please note that the B9403N DC 15w transformer will only accommodate up to 8 of these fittings. 

Installation 12v

Choosing the style of a product is only part of the equation you must also think of where that product will be used and how it will be installed. All exterior lighting products on our web site have an IP rating appropriate to each light fitting and its intended application and is therefore fit for purpose. Water ingress is the enemy for outdoor lighting and the products supplied are only as good as the installation. The weakest point is always cable joints. All joints must be made 100% watertight and this can be done using IP68 cable connectors and/or waterproof junction boxes which are then filled with a re-enterable liquid gel mix. All joints where possible should be made above ground for easy access and reduced water ingress. When installing ground buried lights adequate drainage systems should be put in place especially in clay-based soil areas. If possible, use ground surface spike lights rather than a buried light.  Care must be taken with the cable runs and not to install transformers more than 30 metres away from the furthest fitting to avoid any voltage drop. Cabling should be 2 core Rubber HO5RN-F or HO7RN-F and not PVC. PVC leads to capillary action over time especially with UV degradation. Always check the correct type of transformer you need for your fittings. We recommend wiring in parallel with Toroidal AC and LED DC drivers. But when using Milliamp mA LED drivers, they should always be wired in series. Plug and Play kits are simply a case of daisy chaining the fittings via plug and play junction boxes, connectors and extension cables using a 2-pin plug arrangement. 

All exterior lights must be installed by a certified NIC EIC electrician and should be signed off by an electrician with Part P certification. There are a selection of waterproof jointing kits and boxes available on this web site.




Step lighting example

                           

We would advise parallel wiring for this installation




                                                                  

Item Specifications

colour: Natural Copper, stainless steel 316
Overall diameter: 41mm including pot (recessed sleeve)
Voltage: 12V dc
IP rating: IP 65
Materials: stainless steel 316
Lumens: 60 lm
Material Finish: 316 Stainless Steel
Bulb Type: integral LED
diameter: 38mm
watts: 0.5 watt
colour temperature: 4000k cool white, 2700 warm white
Bezel: Diameter 50mm
Warranty: 2 Years