01689 606342

Waymarker 360 - 12v Copper Bezel & Aluminium Body With 4 Windows Giving 360 Degree Light IP65 MR16       

( Requires a 12v toroidal transformer )


The Waymarker 360 code number E8421L is a stylish 12v recessed light with 4 windows providing 360 degree lighting around the top plate. It is useful where you want to cast a corona of light both across a path or drive edge as well as backwards onto planting, lawn or other areas behind. The light is located by an O ring on the body into a sleeve tube so that no external screw fixings are visible. It may also be used as a deck light.

Not for use in areas prone to waterlogging or flooding 
  
Colour/Finish: Natural copper weathers to a mottled brown finish which blends well with red brick, bark mulch, gravel and timber, especially hardwood decking
IP Rating: IP65
Construction: Top plate is attached to tubular aluminium body which unscrews into 2 halves without tools for easy lamp changing. 2m cable via rear entry cable
Input Voltage: 12v
Lamp Type: MR16  LED lamp - 38 degree beam for wider staircases or 60 degree beam for wider coverage of a narrower staircase, path or patio. MR16 warm white LED. lamps include 3w or 5w for lighting across wider steps; up to 50,000 life and low energy consumption make them the best option
Installation: The plastic sleeve is built into the wall during construction or retrofitted into a hole cut with a coring bit: the light pushes into the tube, where it is held firmly in place by an o-ring, leaving a front plate with no visible fixing screws. Suitable drainage should be provided below each fitting to prevent water logging. Waymarkers should not be installed in ground subject to water logging, an IP68 light such as a Neptune Recessed light should be considered. Connect input cable to cable from transformer using T9962 cable joint or T9963 cable splice kit.

 Please be aware that copper will dull down with the elements of the weather and Patina effect will occur. NOT SUITABLE TO DRIVE OVER.


                                 The cut out of the installation pot is 67.5mm diameter x 120mm depth


                                      The diameter of the body of the fitting is 63.5mm x 90mm length

                                                                                

                                                                                    

Installation 12v

Choosing the style of a product is only part of the equation you must also think of where that product will be used and how it will be installed. All exterior lighting products on our web site have an IP rating appropriate to each light fitting and its intended application and is therefore fit for purpose. Water ingress is the enemy for outdoor lighting and the products supplied are only as good as the installation. The weakest point is always cable joints. All joints must be made 100% watertight and this can be done using IP68 cable connectors and/or waterproof junction boxes which are then filled with a re-enterable liquid gel mix. All joints where possible should be made above ground for easy access and reduced water ingress. When installing ground buried lights adequate drainage systems should be put in place especially in clay-based soil areas. If possible, use ground surface spike lights rather than a buried light.  Care must be taken with the cable runs and not to install transformers more than 30 metres away from the furthest fitting to avoid any voltage drop. Cabling should be 2 core Rubber HO5RN-F or HO7RN-F and not PVC. PVC leads to capillary action over time especially with UV degradation. Always check the correct type of transformer you need for your fittings. We recommend wiring in parallel with Toroidal AC and LED DC drivers. But when using Milliamp mA LED drivers, they should always be wired in series. Plug and Play kits are simply a case of daisy chaining the fittings via plug and play junction boxes, connectors and extension cables using a 2-pin plug arrangement. 

All exterior lights must be installed by a certified NIC EIC electrician and should be signed off by an electrician with Part P certification. There are a selection of waterproof jointing kits and boxes available on this web site.


Item Specifications

Beam Angle: 360 degree 4 slots, 180 degree two slots
colour: Natural Copper, stainless steel 316
Voltage: 12v, 220 - 240v
Max wattage: 35W
IP rating: IP 66
Materials: natural Copper
Material Finish: Natural Copper
Bulb Type: GU10
Bezel: 88mm
Warranty: 5 year