01689 606342

Halbury PIR Lantern 240v - Matt Black Polycarbonate E27 IP44 Security Wall Light With PIR Sensor


The Halbury PIR Lantern is a practical yet stylish Lantern wall light. Suitable for outdoor use and with a matt black finish it offers a traditional lantern look. This version has photocell and PIR technology so is activated by movement, making it ideal for pathways and doorways and as extra security.
  • Complete with built in Photocell & PIR
  • 20 lux on, 2000 lux off. 130 degree detection angle, 8m maximum range with a 5 second to 5 min timer function
  • Matt black textured & frosted pc
  • Constructed from polycarbonate
  • 60W Max E27 GLS (bulb not included)
  • IP44
  • Proj: 98.1mm H: 365.5mm W: 180mm
  • Class 2
  • 2YR Warranty
  • Weight: 0.6 Kg
     

Lamp colour ( Kelvins )
 

The colour of a lamp is defined as a measurement called kelvins. A standard GLS light bulb in your house would be 2,700 kelvins which is in the warm colour spectrum and a lamp with 5,000 kelvins would be at the very cold white spectrum. Getting the right colour temperature of a lamp does matter as the warm colour wavelength helps to soften the tone of the area and gives a warm soft relaxed feel and ideal for colourful flower beds and rockery areas especially with wooden bark and at the other end of the scale a 4,000 to 5,000 kelvin lamp colour would be used against a light background such as white walls or to accentuate grey blueish foliage in shrubs and small trees.  When you buy a new, energy efficient bulb, keep your application and colour scheme in mind and make sure to buy the bulb with a colour temperature to match. 

   

Installation  - See Download for pdf instructions

1. Decide on the position of the light fitting / or remove existing light fitting. Take a note of the position of the electrical connections. Ensure there is a solid mounting surface, for example a brick wall, to support the weight of the light fitting.
2. Remove the shade from the backplate (1 ), retaining the screws for re-use, and use as a template to mark the screw holes ensuring the bracket is horizontal. Make the holes, and secure the backplate with appropriate fittings (2).
3. Remove the diffuser box (3) and fit the bulb (4). NOTE: Never fit bulbs of a higher wattage than those specified on the label (as these may cause overheating and damage the fitting). If the diffuser becomes damaged or broken, it must be replaced.
4. Remove the terminal box and connect the house wiring to the terminal block (5). When you are sure of the connections wrap the Terminal Block and overlap the wiring both sides with 2 layers of insulation tape. NOTE: This is a Class II fitting and must NOT be earthed. Replace the terminal box (6), ensuring a good seal.
5. Replace the shade over the backplate (7), ensuring a good seal, and secure in place.
6. Turn on the power and test.
The PIR sensor settings (8) can be altered by turning the dials under the fitting marked 'LUX' and 'TIME'

The unit must be installed in a vertical position, and fitted 1.8m - 2.5m above the ground.
The PIR sensor can be adjusted using the LUX and TIME dials.
The detection angle is set at 130 degrees, but the distance can be set using the LUX dial (A). The maximum detection distance is Sm.
The PIR will start activating when the light level drops to 20 LUX and will continue to activate until the light level rises to 2000 LUX. When adjusting the sensitivity (detection distance) in daylight it will be necessary to cover the sensor to simulate night time.
The length of time that the light is on can be adjusted by turning the 'Time' dial (B), which can be altered between 5 seconds to 5 minutes duration.                 



Item Specifications

colour: Black
Weight: 0.06kg
Voltage: 240V
Max wattage: 60 w
IP rating: IP 44
Materials: Constructed from polycarbonate
Width: 180mm
Height: 365.5mm
Dimensions: Proj: 100mm H: 370mm W: 180mm
Sensor: PIR
Material Finish: Matt black textured & frosted pc
Bulb Type: E27
Projection: 98.1mm
additional information: complete with Built in PIR
Warranty: 2 Years