01689 606342

Modula Recessed Uplight - Green - Round - 240v GU10 - 30 degree

240v GU10 adjustable recessed uplight for use in lawns - with a choice of halogen, long-life energy-saving compact fluorescent or low-energy LED lamp
E8742N is a stylish 240v recessed uplight with a choice of 240v GU10  LED lamps. Modula is fitted with a flush lens as standard. The light is located by an "O" ring on the body into a sleeve tube. To facilitate removal of screws for future relamping or other maintenance, apply copper grease to the threads of all screws being fitted for retention of bezels, grills or other top plates or retaining rings. Copper grease resists degradation due to heat and protects against difficulty in removing screws, particularly where stainless steel screws are fitted with aluminium parts. It may also be used on screw threads of screw-off bezels or glare shields. Ensure surplus is cleaned off with a solvent to prevent staining in use.
 
 
Colour/Finish: Powder Coated Green blends well in lawns
IP Rating: IP67
Construction: Front bezel is attached to tubular aluminium body. 1m cable via rear entry cable gland
Input Voltage: 240v 
Lamp Type: GU10 halogen, long-life energy-saving compact fluorescent and 3w or 5w l.e.d. lamps; 50,000 life and low energy consumption make these a popular option. l.e.d. and fluorescent lamps also result in a much lower lens temperature, which is important in walkover areas.
Installation:

The plastic sleeve is built in during construction or retrofitted into a hole cut with a coring bit: the light pushes into the tube, where it is held firmly in place by an o-ring.

Using a single RCD for large numbers of 240v fittings is not recommended due to the risk of nuisance tripping. We advise the use of separate RCD protection for each circuit and a maximum of 12 fittings per RCD. Where a garden lighting installation of more than 12 spike mount or recessed lights per circuit is proposed, we suggest the installation of 12v units with transformers, which results in a significantly higher fault tolerance and reliability in the total installation

Light output ( Lumens )

The amount of light that is produced by a lamp is called lumens and the more lumens the lamp has the brighter it will be. Lumens work in conjunction with kelvins and should not be taken in isolation of each other, for example if you had a very warm white lamp at 2,700 kelvins and it produced 300 lumens and you then had another lamp which was a cool white 5,000 kelvins which also produced 300 lumens the cooler lamp colour would always appear brighter to the naked eye than the warmer one this is due to the receptors in the eye that react better to a white light spectrum. Another factor on how bright a light may appear is contrast so if you shine a white 5,000 kelvin light onto a dark wall and a warm 2,700 kelvin lamp onto a white wall the warmer lamp would appear brighter due to the contrast of the material it is focused on. So when choosing a lamp always take into account the area you want to illuminate and think about Kelvins ( colour ),  Lumens ( brightness) and contrast   ( colour of area ) .

                                                       

Installation 

All exterior lighting products on our website have an IP rating which is explained further in our design ideas section but in simple terms the IP rating is appropriate to each light fitting and its intended application and is therefore fit for purpose. Water ingress is the enemy for outdoor lighting and the products supplied are only as good as the installation as the weakest point is always cable joints. All joints must be made 100% water tight and this can be done using IP68 inline connectors, waterproof junction boxes which are then filled with a resin or gel mix. All joints where possible should be made above ground for easy access and reduced water ingress. When installing ground buried lights adequate drainage systems should be put in place especially in clay based soil areas. Also mains cable should be SWA rubber and not PVC.


All exterior lights must be installed by a certified NIC EIC electrician and should be signed off by an electrician with Part P certification. All cable joints must be 100% watertight. There are a selection of waterproof jointing kits and boxes available on this web site.

H05RN-F  3 Core Rubber Sheathed Mains Cable 1.5mm is recommended but do not use PVC flex cable as this can cause poor connections for the cable glands/joints and will lead to capillary action.


Item Specifications

colour: Green
IP rating: IP 67
Degree of tilt: 30
Bulb Type: GU10