01689 606342

Vigor LED Microwave - 240v White Polycarbonate 16w 4200k 1200 Lumens IP65 Emergency Security Light

The high quality Vigor internal or external bulkhead is built to last, manufactured from a strong thermoplastic with a shatterproof polycarbonate diffuser making it suitable for both commercial and domestic applications. Featuring a twist and lock design, these fittings are quick and easy to install; available in a choice of standard, emergency and sensor options.  Non maintained option choose code 50695.

  • Suitable for indoor or outdoor use
  • Complete with built in Microwave sensor
  • 360 /160 degree detection angle, 0 to 50lux sensitivity, 10% to 100% adjustable range with a 5 sec - 15 min timer function
  • Gloss white & opal pc
  • Constructed from polycarbonate
  • Complete with LED driver
  • 16W LED module (SMD 5630) Cool White & 2W LED module (SMD 5630) Cool White (Included)
  • K: 4200 Lm: 1200 Lm/W: 75
  • Can be wall mounted
  • Proj: 110mm Dia: 325mm
  • Emergency maintained fitting
  • Class 1
  • 2+3YR Extended Warranty
  • Weight: 1.6 Kg


Lamp colour ( Kelvins )


The colour of a lamp is defined as a measurement called kelvins. A standard GLS light bulb in your house would be 2,700 kelvins which is in the warm colour spectrum and a lamp with 5,000 kelvins would be at the very cold white spectrum. Getting the right colour temperature of a lamp does matter as the warm colour wavelength helps to soften the tone of the area and gives a warm soft relaxed feel and ideal for colourful flower beds and rockery areas especially with wooden bark and at the other end of the scale a 4,000 to 5,000 kelvin lamp colour would be used against a light background such as white walls or to accentuate grey blueish foliage in shrubs and small trees.  When you buy a new, energy efficient bulb, keep your application and colour scheme in mind and make sure to buy the bulb with a colour temperature to match. 

Installation - See attached downloads

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires. Note that the switch is turned off before installation. Undo screws and set aside. Hold the product in place and mark the position of the holes. Ensure the wall is capable of holding the weight of the product, or if fitting into a ceiling, ensure there is a joist at the point of fixing to support the weight of the product.

Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard. Fix into position. Piece the hole in the grommet, and pull the cable through. Wire as details in the download.

Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product. Refit the shade ensuring the seals are correctly located. Replace fuse or circuit breaker and switch on. Your light is now ready for use.

The unit works in maintained mode. The fitting can be switched separately on or off. The unit will charge automatically (LED is green). A single LED remains on when the supply is interrupted. Locate the fly lead on the inverter and plug into the connector. Replace fuse or circuit breaker and switch on. Ensure that the source is mains 240v~50Hz. Verify that the green LED is illuminated, this confirms that the batteries are charging. Charge the battery for at least 16 hours before first use.

If the LED is not illuminated then there may be no A.C. Supply, the battery has not been connected properly or the terminal or internal circuit have failed. The battery should be re-charged and checked every three months. The battery should be discharged and the duration of the lamp in emergency mode checked every 6 months.

Item Specifications

colour: white
Weight: 1.6kg
Voltage: 240V
IP rating: IP 65
Materials: polycarbonate
Dimensions: Proj: 110mm Dia: 325mm
Technical: Complete with LED driver
Sensor: Microwave Sensor
Sensor_Description: Complete with built in Microwave sensor
Lumens: 1200 lm
Material Finish: Gloss white & opal pc
watts: 16w
colour temperature: 4200 Cool White
additional information: Complete with fixing accessories
Sensor Range: 360 /160° detection angle, with a 5 sec - 15 min timer function
Emergency Maintained: Yes, No
Warranty: 2 Years