01689 606342

Evesham PIR Lantern 240v - Matt Black Polycarbonate 7w 4200k 400 Lumens IP44 Security Wall Light With PIR Sensor


The Evesham wall light is a practical yet traditional looking wall light and comes with built in PIR technology. Suitable for outdoor use the classic lantern design combined with LED technology make it both stylish and energy efficient. Available in black and white colour finishes. White finish code 54556
  • Complete with built in  PIR
  • 20 lux on, 2000 lux off. 130° detection angle, 8m maximum range with a 5 second to 5 min timer function
  • Matt black textured & frosted pc
  • Constructed from polycarbonate
  • Includes push fit terminal for quick and easy installation
  • Complete with LED driver
  • 7W LED module (SMD 5630) Cool White (Included)
  • K: 4200 Lm: 400 Lm/W: 57
  • IP44
  • Proj: 230mm H: 380mm W: 170mm
  • Class 2
  • 2+1YR Extended Warranty
  • Weight: 0.6 Kg

Lamp colour ( Kelvins )
 

The colour of a lamp is defined as a measurement called kelvins. A standard GLS light bulb in your house would be 2,700 kelvins which is in the warm colour spectrum and a lamp with 5,000 kelvins would be at the very cold white spectrum. Getting the right colour temperature of a lamp does matter as the warm colour wavelength helps to soften the tone of the area and gives a warm soft relaxed feel and ideal for colourful flower beds and rockery areas especially with wooden bark and at the other end of the scale a 4,000 to 5,000 kelvin lamp colour would be used against a light background such as white walls or to accentuate grey blueish foliage in shrubs and small trees.  When you buy a new, energy efficient bulb, keep your application and colour scheme in mind and make sure to buy the bulb with a colour temperature to match. 

   

Installation  - See Download for pdf instructions


Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.

• The help of an assistant is recommended when installing this fitting.
• Remove the finials from the front of the product and lift the light fitting body away from the wall back. Keep the finials in a safe place for refitting later.
• Using the wall back as a template, mark the position of the mounting holes. Drill holes and fit supplied wall plugs (suitable for masonry only - for other surfaces use appropriate fixings). Feed the incoming mains supply cable through the grommet entry hole. Fix the wall back to the wall using the supplied screws (See Fig. 1).

This product is double insulated and must not be earthed. If there are any incoming earth cables, they must be joined together and well insulated with good quality insulation tape. This is to ensure earth continuity throughout your property.Remove the cover from the mains terminals and having correctly identified the wiring from your existing light fitting, connect to the quick fit connection block in the following way:

Place the light fitting over the threads of the securing screws and refit the rubber washers and finials to secure. Make sure the fitting is correctly oriented in a vertical direction. Replace fuse or circuit breaker and switch on. Your light is now ready for use.

The unit must be installed in a vertical position, and fitted 1.8m - 2.5m above the ground.
The detection angle is set at 130 degrees and the detection distance is 8m. The PIR will start activating when the light level drops to 20 LUX and will continue to activate until the light level rises to 2000 LUX. When adjusting the sensitivity (detection distance) in daylight it will be necessary to cover the sensor to simulate night time. When the PIR is activated the light will remain lit for  a maximum of 5 minutes. The minimum is 5 seconds.

The LED bulb in this product are non replaceable.


Item Specifications

colour: white, Black
Weight: 0.6kg
Voltage: 240V
IP rating: IP 44
Materials: polycarbonate
Width: 170mm
Height: 380mm
Sensor: PIR
Sensor_Description: 30 lux on, 70 lux off. 130 degree detection angle, 8m maximum range with a 4 min timer function
Lumens: 400 lm
Material Finish: Matt black textured & frosted pc
Bulb Type: integral LED
watts: 7w
colour temperature: 4200 Cool White
Projection: 230mm
additional information: Not suitable with a dimmer switch
Warranty: 2 Years