01689 606342

Navigator eye,12v, 1w LED step light, copper, 2700k warm white, IP65


                                                                          ( Requires a 12v transformer )



The E3421WW is a low energy, high output warm white LED deck and recessed light which consumes a small amount of power and stays cool to the touch. The warm white LED produces a wide 80° beam diffused by the 28mm diameter frosted lens to provide soft lighting compatible with the colour of halogen garden lighting. Install it to light across individual steps or in a wall about 40cm above a patio or deck. 

Natural Copper weathers to a mottled brown finish which blends well with red brick and timber, especially darker hardwood decking.
Rated at IP65 1w 2700k warm white LED and 101 lumen output. 
The LED is a long life high-output resin encapsulated module behind a frosted glass lens in a stainless steel case. The case has a spring mount which locates the light in a sleeve used to prepare positions in concrete, paving and walls. It comes supplied with H05RN two core cable. They can be recessed without the sleeve in decking sleeper walls and other materials using a 44mm hole saw. Diameter 60mm (sleeve 48mm, 44mm cutout without sleeve), recess depth 75mm.

The input voltage is 12v 1.5w, Navigators should be powered by 12v DC power supplies. Do not use an electronic transformer to power Navigator LED lights. If powered from a 12v AC wire wound (toroidal) transformer, ensure the transformer is loaded to at least 75% of nominal rating. MUST BE WIRED IN PARALLEL.

Navigators can be arranged in custom layouts using cable joint kits and 2 core 12v rubber H05RN cable supplied by reel, which is more flexible than kit-type products. Connect to end of a low voltage cable using T9962 cable joint kit, for splicing into a run of cable use T9963 cable splice kits. Supply from magnetic transformer such as the T9502 surface mount 20va or T2504 ground burial transformer, not an electronic transformer.

To outline a deck or patio space with a distinctive shape, start at the corners of the decking or paving and space LED recessed garden lights at about 1 - 1.5m apart.
                                                         


A guide to lighting steps




Installation 12v

Choosing the style of a product is only part of the equation you must also think of where that product will be used and how it will be installed. All exterior lighting products on our web site have an IP rating appropriate to each light fitting and its intended application and is therefore fit for purpose. Water ingress is the enemy for outdoor lighting and the products supplied are only as good as the installation. The weakest point is always cable joints. All joints must be made 100% watertight and this can be done using IP68 cable connectors and/or waterproof junction boxes which are then filled with a re-enterable liquid gel mix. All joints where possible should be made above ground for easy access and reduced water ingress. When installing ground buried lights adequate drainage systems should be put in place especially in clay-based soil areas. If possible, use ground surface spike lights rather than a buried light.  Care must be taken with the cable runs and not to install transformers more than 30 metres away from the furthest fitting to avoid any voltage drop. Cabling should be 2 core Rubber HO5RN-F or HO7RN-F and not PVC. PVC leads to capillary action over time especially with UV degradation. Always check the correct type of transformer you need for your fittings. We recommend wiring in parallel with Toroidal AC and LED DC drivers. But when using Milliamp mA LED drivers, they should always be wired in series. Plug and Play kits are simply a case of daisy chaining the fittings via plug and play junction boxes, connectors and extension cables using a 2-pin plug arrangement. 

All exterior lights must be installed by a certified NIC EIC electrician and should be signed off by an electrician with Part P certification. There are a selection of waterproof jointing kits and boxes available on this web site. 


Item Specifications

colour: Natural Copper, stainless steel 316
Cut out: 44mm fitting and 48mm for the recess sleeve
Installation depth: 75mm
Overall diameter: 48mm including pot (recessed sleeve)
Voltage: 12V dc
IP rating: IP 65
Depth: fitting 54mm
Lumens: 101 lm
Material Finish: 316 Stainless Steel
Bulb Type: integral LED
diameter: 44mm
watts: 1w
colour temperature: 3000k Warm White, 4000k cool white, 2700 warm white
cabling: 2m H05RN two core cable
Bezel: 60mm diameter
Warranty: 2 Years